SWITNEX AC85-250V Universal Wireless Remote Control Switch User Manual
| Technical Data | |
|---|---|
| Model Number | 2201H |
| Connectivity Technology | Radio Frequency (433MHz) |
| Receiver Input Voltage | AC 85V-250V |
| Max Current | 30A |
| Max Range | 50 meters (164 feet) without obstacles |
| Number of Buttons (Remote) | 2 (ON/OFF) |
| Max Supported Transmitters | 20 pieces |
| RF frequency | 433MHz |
| Support encoding | 1527 Leaning code、2262 fixed code |
| RF Operating mode | ASK superheterodyne wireless reception |
| Working temperature | -30~+80 |
| Receiving Sensitivity | >97dbm |
| Quiescent Current | <5MA |
Product Detail
- Receiver unit includes: antenna for signal reception, protective shell, indicator light, learning button for programming
- Remote control features: 'ON' and 'OFF' silicone buttons, chrome bezel, metal keychain for portability
- NO: Normally open pin
- COM: Common pin
- NC: Normally closed pin
- Output Type: Active output (or passive output / potential-free contacts as applicable)
Wiring Diagram
Warning
- Always disconnect power before performing any wiring or maintenance.
- Ensure all connections are secure and properly insulated to prevent short circuits.
- Do not exceed the maximum current rating of 30A for the relay.
- Operate the device within the specified voltage range of AC 85V-250V.
- Keep the device away from water and high humidity environments.
- If you are unsure about electrical wiring, consult a qualified electrician.
- Usually the receiver and transmitter have been paired with each other in factory. If not, please reprogram them.
- Reset before you want to change the operating mode.
- After reset, all the remote controls cannot work anymore.
- Replace the battery in time when the remote transmitter voltage is low to get stronger signal transmission.
- Slightly stretch the antenna on the receiver for better signal reception.
Operating Mode
Momentary Mode (Mode 1)
Press and hold the remote button → relay turns on (output ON)
Release the button → relay turns off
How to program:
- Press the learning button on the receiver 1 time. The indicator light will flash once.
- Press any button on your remote control. The indicator light will flash three times, confirming successful pairing in Momentary Mode.
Toggle Mode (Mode 2)
Press the remote button once → relay turns on (output ON)
Press the same button again → relay turns off
How to program:
- Press the learning button on the receiver 2 times. The indicator light will flash twice.
- Press any button on your remote control. The indicator light will flash three times, confirming successful pairing in Toggle Mode.
Latched Mode (Mode 3)
Press the ON button → relay turns on
Press the OFF button → relay turns off
How to program:
- Press the learning button on the receiver 3 times. The indicator light will flash three times.
- Press the ON button on your remote control.
- Press the OFF button on your remote control. The indicator light will flash three times, confirming successful pairing in Latched Mode.
Delay Mode (Mode 4/5/6/7)
Press the remote button → relay turns on (output ON)
After the set delay time, relay automatically turns off
Delay options:
- Mode 4 (press learning button 4 times): 5-second delay
- Mode 5 (press learning button 5 times): 10-second delay
- Mode 6 (press learning button 6 times): 15-second delay
- Mode 7 (press learning button 7 times): 20-second delay
How to program:
- Press the learning button on the receiver the desired number of times (4, 5, 6, or 7). The indicator light will flash accordingly.
- Press any button on your remote control. The indicator light will flash three times, confirming successful pairing in Delay Mode.
Reset
Press the learning button on the receiver 8 times. The indicator light will flash eight times and then turn off, indicating a successful reset. After reset, the remote control will no longer function until re-paired.
Troubleshooting
If the receiver and transmitter cannot operate normally, try the following steps:
- Remote not responding: Ensure the receiver is powered on and the remote control has a working battery. If the receiver was recently reset, re-pair the remote control following the programming instructions.
- Appliance not turning ON/OFF: Check all wiring connections for tightness and proper insulation. Verify that the power supply to the receiver is active and within the specified voltage range (AC 85V-250V).
- Reduced remote range: Large metal objects, thick walls, or other radio frequency devices can interfere with the signal. Try repositioning the receiver or remote control.
- Indicator light not flashing during programming: Ensure you are pressing the learning button correctly and for the appropriate duration as specified for each mode.
- Battery check: The indicator LED on the remote transmitter does not light up or is dimly lit – replace the battery.
Maintenance
- Keep the receiver and remote control clean and free from dust and debris.
- Avoid exposing the devices to extreme temperatures, direct sunlight, or moisture.
- Replace the remote control battery when its performance degrades.
- Periodically check wiring connections for any signs of wear or damage.
Contact
- WhatsApp: +86 15812381273
- Email: linktrol@icloud.com
If there is any question about the products, please contact us first. We will do our best to solve your problem. Thank you.