SWITNEX AC85-250V 1-Channel Wireless Remote Control Relay Switch
| Technical Data | |
|---|---|
| Operating Frequency | 433MHz |
| Receiver Voltage | AC 100V~250V |
| Relay Type | Potential-Free Contacts (Dry Contacts) |
| Relay Current | 5A |
| Control Range | Up to 30 meters (open area) |
| Learning Code | EV1527 |
| Transmitter Battery | 2x CR2016 or 1x CR2032 (included) |
| Components Included | 1 Receiver, 5 Transmitters |
Product Detail
- NO: Normally open pin
- COM: Common pin
- NC: Normally closed pin
- L: Live input terminal (AC 100V-250V)
- N: Neutral input terminal
- Learning button on receiver – for programming modes and resetting
- Indicator LED on receiver – provides visual feedback
- Antenna on receiver – for signal reception
- 5 x Transmitters (remote controls) – each with ON/OFF buttons, powered by CR2016 or CR2032 batteries
Wiring Diagram
- Power input: Connect AC 100V-250V to L (Live) and N (Neutral) terminals
- Relay output (dry contacts): NO, COM, NC
- For AC device: Connect live wire from power source to COM, live wire of device to NO; neutral wires direct
- For DC device: Connect positive of DC power source to COM, positive of device to NO; negative direct
- For garage door opener: Connect NO and COM in parallel with existing wall button terminals
Warning
- Always disconnect power before installing or performing any maintenance on the receiver module.
- Ensure all wiring is done by a qualified professional if you are unsure.
- Do not exceed the maximum current rating of 5A for the relay.
- Do not expose the device to moisture or extreme temperatures.
- Verify correct voltage (AC 100V-250V) before connecting any appliance.
- Keep remote controls out of reach of children.
- Usually the receiver and transmitter have been paired in factory. If not, reprogram them.
- Reset before you want to change the operating mode.
- After reset, all remote controls cannot work anymore.
- Replace the battery in time when the remote transmitter voltage is low.
Operating Mode
The default mode is Latched Mode. Follow the programming steps below to change modes.
Momentary Mode
Press and hold a button → relay activates (device ON)
Release the button → relay deactivates (device OFF)
How to program:
- Press the learning button on the receiver 1 time. The indicator light will flash.
- Press any button on the remote control. The indicator light will flash, confirming successful programming.
Toggle Mode
Press a button once → relay activates (device ON)
Press the same button again → relay deactivates (device OFF)
How to program:
- Press the learning button on the receiver 2 times. The indicator light will flash.
- Press any button on the remote control. The indicator light will flash, confirming successful programming.
Latched Mode
Press ON button → relay activates (device ON)
Press OFF button → relay deactivates (device OFF)
How to program:
- Press the learning button on the receiver 3 times. The indicator light will flash.
- Press the ON button on the remote control.
- Press the OFF button on the remote control. The indicator light will flash, confirming successful programming.
Delay Mode
Press a button → relay activates (device ON) and stays on for a set delay, then automatically turns OFF
Delay options:
- Mode 4 (press learning button 4 times): 5-second delay
- Mode 5 (press learning button 5 times): 10-second delay
- Mode 6 (press learning button 6 times): 15-second delay
- Mode 7 (press learning button 7 times): 20-second delay
How to program:
- Press the learning button the desired number of times (4, 5, 6, or 7). The indicator light will flash.
- Press any button on the remote control. The indicator light will flash, confirming successful programming.
Reset
To clear all stored remote control codes from the receiver, press the learning button 8 times. The indicator light will flash 8 times and then turn off, indicating successful reset. After reset, the remote control will not operate the receiver until reprogrammed.
Troubleshooting
If the receiver and transmitter cannot operate normally, try the following steps:
- Device not responding: Check power supply to receiver (AC 100V-250V). Ensure remote batteries are not depleted. Verify remote is correctly programmed. Check for obstructions or excessive distance.
- Intermittent operation: Replace remote batteries. Ensure antenna is not obstructed. Minimize RF interference from other devices or metal objects.
- Incorrect mode operation: Reset the receiver (press learning button 8 times) and reprogram the desired mode.
Maintenance
- Battery replacement (remote control): Replace with 2x CR2016 or 1x CR2032 when range decreases or LED is dim. Ensure correct polarity.
- Cleaning: Wipe the receiver and remote controls with a soft, dry cloth. Do not use liquid cleaners or solvents.
- Store devices in a dry, dust-free environment.
Contact
- WhatsApp: +86 15812381273
- Email: linktrol@icloud.com
If there is any question about the products, please contact us first. We will do our best to solve your problem. Thank you.